Senarai Kesalahan Bilik Sejuk dan Panduan Utama Penyelesaian Masalah

What to Do Immediately After a Cold Room Failure

When a sudden malfunction occurs, you can take emergency measures to minimize your losses.

1. Minimumkan bukaan pintu:

Restrict unnecessary entry and exit immediately, suspend non-essential loading or picking, and keep the cold room door closed as much as possible to reduce cold air loss.

2. Protect high-value and temperature-sensitive products first:

Prioritize seafood, daging, produk tenusu, farmaseutikal, and other high-value or temperature-sensitive goods for transfer.

Products with lower spoilage risk can handle afterwards.

3. Record key operating data:

Document the current room temperature, set temp, alarm codes, time of failure, suhu ambien, and any visible signs such as unusual noise, water leakage, or frost buildup.

Accurate records can help service teams identify the problem more efficiently.

4. Carry out basic checks:

Check the power supply, circuit breaker, controller alarms, door sealing condition, evaporator frosting level, and whether the condenser area is blocked or poorly ventilated.

5. Isolate risks:

If there is water leakage, a burning smell, abnormal noise, repeated breaker trips, or any other sign of electrical or mechanical danger, stop forcing the system to run in order to prevent further damage.

6. Contact your supplier promptly:

Share on-site photos, video, alarm information, and operating data as early as possible.

This can shorten communication time, improve diagnosis accuracy, and speed up the recovery process.

Quick diagnostic List

Next step, you should have a quick diagnostic by yourselves to define the basic faults of your cold room:

Kesilapan	Likely causes	What to check first	Who should handle
Bilik sejuk tidak cukup sejuk	Door leaks, dirty condenser, low refrigerant, airflow blockage	Door closing, set temp, coil cleanliness, product stacking	Operator / Technician
Ice on evaporator	Defrost failure, door air leakage, kelembapan yang tinggi, low airflow	Defrost cycle, gasket, kipas, drain	Operator / Technician
Water on floor	Blocked drain, defrost issue, door seal leak	Drain line, pan, gasket, floor slope	Operator / Technician
Compressor not running	Power loss, breaker trip, controller fault, compressor fault	Breaker, power supply, controller alarm	Technician
Kebocoran bahan pendingin	Corroded pipes, sendi longgar, vibration damage, poor installation	Oil stains, pressure drop, cooling performance, leak points	Technician
Condenser fan not running	Kegagalan kuasa, faulty motor, capacitor damage, wiring issue, obstruction	Fan blades, power supply, kapasitor, suhu motor	Operator / Technician
Compressor making loud noise	Loose parts, worn bearings, slugging cecair, getaran, internal damage	Noise source, mounting bolts, piping vibration, oil level	Technician
Poor airflow	Blocked evaporator, fan failure, dirty filters, overstocking, poor layout	Fan operation, air path, product spacing, coil condition	Operator / Technician
Sensor malfunction	Sensor failure, loose wiring, wrong placement, controller error, calibration drift	suhu bilik, sensor position, wiring, actual room temperature	Operator / Technician
Power outage	Utility failure, tripped breaker, loose connection, overload, kehilangan fasa	Main supply, breaker, voltan, alarm display	Operator / Technician

Absolutely, the quick diagnostic list is not specific enough, so we should know more details about the faults and solution.

Detailed Troubleshooting Sections

Bilik sejuk tidak cukup sejuk

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Cold room temperature is higher than set	Incorrect thermostat setting, dirty condenser coil, airflow block, door gasket damage, low refrigerant, sensor error	Check the controller setting, inspect condenser cleanliness, confirm the door closes tightly, review product stacking, compare current temperature with an independent thermometer	Adjust the set temp, clean condenser, improve airflow clearance, replace damaged door gaskets, and arrange refrigerant or sensor inspection	ya, if cooling doesn't recover after basic checks

Additional Note:

The most common causes are dirty condenser coils, kerap membuka pintu, poor product stacking, and door air leaks. Start with the easiest checks first: setpoint, door closing, airflow path, and coil cleanliness.

If the room temperature keeps rising or stored goods are temperature-sensitive, move products if possible and contact a technician immediately.

Notis: For more troubleshootings about this faults, please check the post “Mengapa Bilik Sejuk Anda Tidak Sejuk?”

Ice Buildup on Evaporator

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Ice or frost is building up on the evaporator coil	Defrost failure, kelembapan yang tinggi, door gasket damage, evaporator fan failure, blocked drain, low airflow	Check whether the defrost cycle is working, inspect the gasket, confirm the fan is running, look for blocked air passages, inspect the drain line	Restore normal defrost operation, replace damaged gaskets, clear airflow obstructions, clean the drain, and remove excessive ice safely	ya, if icing returns quickly or the defrost system is faulty

Additional Note:

A failed defrost cycle and warm moist air entering through the door are the most common reasons.

First check whether the unit is in normal defrost mode or if frost is building abnormally fast.

If heavy icing reduces airflow or the room can’t hold temperature, maybe affect product quality.

Evaporator Coil Ice/Frost

Water leak

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Water is leaking inside or around the cold room	Blocked drain line, defrost water overflow, door gasket damage, excessive condensation, improper floor slope	Inspect the drain line and pan, check for ice blocking the drain, inspect door sealing, look at the floor area and defrost water path	Clear the drain, clean the pan, fix door sealing problems, improve drainage, and check the defrost system if leakage continues	ya, if leakage repeated or linked to the defrost system

Additional Note:

The most common issue is a blocked or frozen drain line.

Check where the water appears: near the evaporator, near the door, or across the floor.

If water creates slip hazards, mold risk, or repeated pooling, then shoud inspect system promptly.

Notis: For more troubleshootings about this faults, please check the post “Mengapa Bilik Sejuk Anda Bocorkan Air?”

Pemampat tidak Berjalan

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The compressor doesn't start or stop completely	Kegagalan kuasa, tripped breaker, faulty controller, overload protection, wiring fault, compressor failure	Check the main power supply, breaker status, controller alarm, contactor condition, and whether the compressor is hot or silent	Reset power if safe, restore electrical supply, check controller settings, and arrange compressor or electrical diagnosis if the unit still doesn't start	ya, in most cases

Additional Note:

Often check power supply issues and control faults first, because they are easier to confirm than internal compressor damage.

If the breaker keeps tripping or the compressor overheats, stop trying to restart it repeatedly.

Continued restart attempts can worsen damage and increase downtime.

Pemampat Copeland

Kipas Kondenser tidak Berfungsi

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The condenser fan does't spin or runs abnormally	Power issue, faulty motor, failed capacitor, loose wiring, physical obstruction, fan blade damage	Check whether the fan blade is blocked, inspect the power supply, listen for motor hum, inspect visible wiring, and feel for overheating around the motor area	Keluarkan halangan, replace damaged blades, repair wiring, and replace the motor or capacitor if faulty	ya, if the motor or electrical parts are defective

Additional Note:

A non-running condenser fan can quickly cause high condensing pressure and poor cooling performance.

First check for obvious blockage and confirm that the fan is receiving power.

If the compressor is still running while the fan is not, should arrange service quickly to avoid further damage.

Poor Airflow

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Air circulation inside the cold room is weak or uneven	Overstocking, blocked evaporator, fan failure, dirty filters, poor product layout, ice buildup	Check the distance between products and walls, inspect evaporator airflow, confirm fan operation, and look for blocked air outlets or returns	Rearrange stored goods, clear air paths, clean filters, restore fan operation, and remove ice if present	ya, if airflow remains poor after layout and cleaning checks

Additional Note:

Overstocking and blocked air passages are the most common causes.

Check whether cartons or pallets are blocking supply air or return air.

Poor airflow often causes uneven room temperature, which can lead to hidden product loss even when the controller looks normal.

Sensor Malfunction

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The displayed temperature is inaccurate or unstable because of sensor problems	Sensor failure, loose wiring, wrong sensor position, controller error, calibration drift	Compare the displayed temperature with a calibrated thermometer, inspect sensor placement, check wiring connections, and review controller alarms	Reposition the sensor, repair loose wiring, recalibrate, and replace the sensor if faulty	ya, if need recalibration or replacement

Additional Note:

A sensor problem can make the room appear normal on the display even when the actual storage temperature is wrong. First compare controller readings with an independent thermometer placed in the product zone.

If difference is large or readings fluctuate abnormally, product safety may be at risk.

Power Outage

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The cold room loses power fully or intermittently	Utility outage, tripped breaker, overloaded circuit, loose connection, kehilangan fasa, distribution fault	Check the main power supply, breaker panel, voltan, alarm display, and whether affect other equipment	Restore utility power, reset breaker, reduce overload, and inspect the electrical supply path	ya, if power doesn't return normally or faults repeat

Additional Note:

A complete outage is often easy to identify, but intermittent power loss is more dangerous because it causes unstable temperatures and hard-to-trace shutdowns.

Confirm whether outage is isolated to the cold room or affects the whole site.

During outage, keep doors closed as much as possible to reduce temperature rise.

Turun naik suhu

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Room temperature rises and falls too often	Sensor error, controller setting problem, door opening frequency, poor insulation, low airflow, refrigeration control fault	Review temperature records, compare actual and displayed temperature, inspect doors, aliran udara, penebat, and controller settings	Correct settings, improve door management, restore airflow, inspect insulation, and service control components if fluctuation continues	ya, if fluctuation is frequent or severe

Additional Note:

Frequent temperature swings usually indicate a control or usage problem rather than a single simple fault.

Check whether door opening patterns or overloading are causing sudden heat gain.

If the stored goods are highly sensitive, even short fluctuations may create quality risks.

Refrigerant Leak

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Refrigerant is leaking from the refrigeration system, causing poor cooling performance and unstable operation	Pipe corrosion, leaking joints, vibration damage, poor brazing, component wear, improper installation	Inspect the system for oil traces, check whether the room is cooling more slowly than usual, look for icing or abnormal temperature differences, and inspect common leak points such as joints, injap, and pipe connections	Identify and repair the leaking point, replace damaged pipes or joints, pressure-test the system, evacuate it properly, and recharge refrigerant to the correct amount after the leak is fixed	ya

Additional Note:

The most common causes are corroded pipework, sendi longgar, vibration-related damage, and poor installation quality.

Check visible oil residue on copper pipes, penyambung, injap, and welded joints, because refrigerant leaks are often accompanied by oil marks.

Product loss may occur if the room temperature rises slowly and the issue is not noticed in time.

Contact a qualified technician immediately if cooling performance drops, the compressor runs longer than usual, or suspect a refrigerant leak.

Refrigerant Leak Test

Door Seal Problem

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The cold room door doesn't seal tightly	Worn gasket, door misalignment, frame damage, poor installation, debris on the seal surface	Inspect gasket condition, check for visible gaps, test door closing, and inspect frame alignment	Clean the sealing area, replace the gasket, adjust door alignment, and repair frame issues	ya, if need alignment or frame repair

Additional Note:

Door sealing problems are a very common root cause behind temperature loss, icing, dan pemeluwapan.

Check for visible air gaps and signs of moisture around the door perimeter first. If the door doesn’t self-close correctly, should correct the issue quickly.

Bunyi pelik

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Unusual noise comes from the compressor, kipas, piping, or unit cooler	Loose fasteners, fan blade contact, piping vibration, worn motor bearings, compressor internal wear, slugging cecair	Identify the noise source, inspect fan blades and guards, check mounting bolts, inspect piping supports, and observe when the noise occurs	Tighten loose parts, correct vibration points, replace damaged fans or motors, and inspect compressor condition if noise remains	ya, if the source is internal compressor damage or repeated heavy vibration

Additional Note:

Not all noise means major failure, but should never ignore sudden or increasing noise.

First determine whether the sound comes from the fan, pemampat, or vibrating pipe.

If knocking, hammering, or metal friction is present, stop the unit and arrange inspection.

High Energy Consumption

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The cold room uses more electricity than normal	Dirty condenser, door air leaks, poor insulation, low airflow, incorrect set temp, overworked compressor, frequent defrost	Compare power bills and runtime, inspect door sealing, check coil cleanliness, review setpoint, aliran udara, and operating patterns	Clean coils, improve sealing, optimize set temp, improve airflow, reduce unnecessary door opening, and inspect system efficiency	ya, if energy use stays high after basic corrections

Additional Note:

Many users first notice an energy cost increase before they notice a cooling fault.

Check dirty coils, pengedap yang lemah, and set temp because these are common and easy to fix.

If energy use rises together with unstable temperature, the issue may be deeper than routine maintenance.

Technician-level Faults

Below faults need skilled knowledge in refrigeration industry, so only need technicians to handle.

Bahan penyejuk Caj berlebihan

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Too much refrigerant has been charged into the system	Incorrect servicing, charging without proper measurement, misdiagnosis after repair	Check system pressures, keadaan operasi, condenser performance, and evaporator behavior	Have the refrigerant charge corrected according to system requirements and operating data	ya

Additional Note:

This is a technician-level fault and shouldn’t handle by normal operators.

It is usually related to previous service work rather than daily operation.

Incorrect handling can damage efficiency and system performance.

Air in System

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Non-condensable gas is present in the refrigeration system	Incomplete evacuation, improper servicing, leakage during repair, poor charging procedure	Check abnormal pressure behavior, discharge temperature, and service history	Recover refrigerant if required, evacuate the system correctly, and recharge under proper service procedure	ya

Additional Note:

Air in the system is not a normal user-maintenance problem. It is usually related to installation or servicing quality.

If suspected, should check whole system with proper tools and procedures.

Notis: If you want to know more troubleshootings about this faults, please check the post “Cara Mengeluarkan Udara Di Dalam Sistem Penyejukan?”

TXV Blockage

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The thermostatic expansion valve is restricted or blocked	Moisture contamination, dirt in the system, filter drier problem, poor evacuation	Check superheat behavior, liquid line condition, filter drier status, and evaporator feeding pattern	Replace blocked components, correct contamination issues, and restore proper system drying and charging	ya

Additional Note:

This fault is usually tied to contamination or moisture inside the refrigeration circuit.

It is not suitable for end users to repair directly.

If the evaporator is starved and cooling drops sharply, need technician service.

Frozen Oil in Evaporator Pipeline

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
Oil accumulates and affects refrigerant flow or heat exchange	Poor oil return, piping design issue, long-term operation imbalance, low load condition	Check cooling performance, piping condition, evaporator behavior, and service history	Diagnose oil return conditions, correct piping or operating issues, and clean the affected section	ya

Additional Note:

This is a deeper refrigeration circuit issue.

Most buyers and operators don’t need repair steps here, but they do need to know the symptom and when to call for service.

Short Cycling

Fault detail	Possible causes	How to check	Penyelesaian	Need technician?
The compressor starts and stops too frequently	Control fault, sensor issue, low refrigerant, high head pressure, wrong settings, electrical problem	Observe cycle frequency, check controller settings, inspect sensor readings, and review system pressures	Correct settings, inspect controls and sensors, and diagnose refrigeration or electrical causes before restarting repeatedly	ya

Additional Note:

Short cycling increases wear and energy use very quickly.

First confirm that the problem is real and not just a normal defrost or pull-down cycle.

If repeated starts happen within short intervals, should inspect the unit before damage worsens.

Preventive maintenance checklist

Daily: Check the room temperature, alarm status, door closing, and any visible ice or water.

Weekly: Clean the coil and fan area, inspect door gaskets, and make sure airflow is not blocked.

Monthly: Inspect wiring, check sensor accuracy, look for signs of refrigerant leaks, and clean the drain system.

Soalan Lazim

S1: How can I quickly determine which category of problem it is: pemampat, bahan penyejuk, pengawal, or door sealing?

Incorrect display or unstable reading usually points to controller/sensor issues; visible gaps, condensation, or frost near the door suggest sealing problems; weak cooling with long runtime may indicate refrigerant loss; repeated trips, failure to start, or loud mechanical noise often suggest compressor or electrical faults.

S2: Which faults indicate that the unit selection is incorrect and requires reconfiguration, rather than repair?

If the cold room never reaches set temperature under normal load, runs almost continuously, recovers too slowly after door opening, or shows long-term short cycling/high energy use despite proper maintenance, the unit may oversize or undersize rather than simply faulty.

S3: Which parts are most prone to failure, so need to prepare backup?

The most failure-prone parts: door gaskets, motor kipas penyejat, condenser fan motors, sensors/probes, pengawal, contactors/capacitors, drain heaters, pengering, valve, and defrost-related components.

S4: What are the differences in common faults between different temperature cold room (Sebagai contoh: 0~5°C chiller, -18°C freezer)?

Chillers more often suffer from poor cooling, condensation, and door air leakage, while freezers are more prone to evaporator icing, defrost problems, frozen drains, and door frost.

Kesimpulan

Secara ringkasnya, understanding common cold room faults and taking the right action early can help reduce downtime, prevent product loss, and improve system reliability.

A clear troubleshooting process, combined with regular maintenance, can make cold room operation more efficient and cost-effective.